patent numbers 5713755 / 5961339 do not scale from this print 2 max sway (either direction) "a" "a" rhle-50-d no of pos x .100 [2.54] .200 5.08 ref .020 ref 0.51 .100 2.54 ref ({no of pos - 1} x .100 [2.54]) .005 [.13] c-132-12-xxx c1 +.008 [.20] -.005 [.13] 01 02 .144 3.66 .259 6.57 90 3 .146 3.71 section "a"-"a" c8 c7 see table 2 .0625 1.588 .050 1.27 [.20 x 1.42] .008 x .056 ref (no of pos -2) x.1000 [2.540] .050 1.27 sm-a10h lc-08-tm-01 c4 -a & -lc option fig 2 c5 hle-1xx-02-xxx-dv-xx-xx-xx no of positions -02 thru -50 (per row) row specification -dv: double vertical (use rhle-50-d) lead style -02: surface mount (use c-132-12-x) plating specification -g: 20" gold in contact area 3" on tail (use c-132-12-g) -s: 30" selective gold in contact area matte tin on tail (use c-132-12-s) -f: 3" selective flash gold in contact area matte tin on tail (use c-132-12-f) -l: 10" selective light gold in contact area matte tin on tail (use c-132-12-l) -h: 30" heavy gold in contact area 3" on tail (use c-132-12-h) -stl: 30" selective gold in contact area tin/lead (90%/10 +/-5%) (use c-132-12-stl) -sm: 30" selective gold in contact area matte tin on tail (use c-132-12-s) -fm: 3" selective flash gold in contact area matte tin on tail (use c-132-12-f) -lm: 10" light gold in contact area matte tin on tail (use c-132-12-l) option -tr: tape & reel (2 - 29 positions only) option option -be: bottom entry (use rhle-50-dbe)(see fig. 5) (leave blank for standard) -p: pick & place pad (pos -03 thru -50 only) -a: alignment pin (4 pos min) -lc: locking clip (2 pos min) (see note 9) -k: polyamide film pad (available on pos -03 thru -50; .005 [.13] thickness with silicone adhesive) (see fig 4) fig 5 -be option (same as fig 1 unless otherwise stated) rhle-50-dbe fig 1 hle-116-02-xxx-dv shown c c3 sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [.3] 3 .xxx: .005 [.13] .xxxx: .0020 [.051] material: [2.54] .100 tiger beam socket assembly by: hle-1xx-02-xxx-dv-xx-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing ed messer 12/19/98 2 1 sheet scale: 2:1 body: vectra e130i contact: becu f:\dwg\misc\mktg\hle-1xx-02-xxx-dv-xx-xx-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. all identification marks must not stand greater than .002 [.05] off the surface of the part. 3. pull out force for -lc, -a, & contact is 12 oz min. 4. coplanarity: see table 2. 5. burr allowance: .003 [.08] max 6. cut assemblies after fill. cut flash to be .010 max with no flash allowed in holes or extending below leads. will lose a position for every cut made on a socket strip. 7. tube positions 03 thru 50. layer package position 02. 8. endwall thickness: .030+/-.005[.76+/-.13] to be measured from bottom view. 9. due to the high amount of insertion force needed, the Clc option is not compatible with auto placement. samtec recommends manual placement for all assemblies with the Clc option. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision ag
tube views pt-1-24-01-64 pt-1-24-10-63 .2559 6.500 .028 .010 [.71 .25] "s" (see note) "r" (see note) k-500-300 fig 4 -k: polymide film pad available on pos 03 thru 50 note: "r" = use measured dim (ref) "s" = {("r" - .2559 [6.500])/2} .020 [.51] c6 .149 3.78 c9 "r" .152 3.86 "s" .225 5.72 lmp-02 fig 3 (-p: pick and place pad) available on positions 03 thru 50 note: "r" = use measured dim (ref) "s" = {("r" - .225 [5.72])/2} .020 [.51] c10 .280 7.11 c2 sheet of .100 tiger beam socket assembly by: dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing ed messer 12/19/98 2 2 sheet scale: 2:1 revision ag f:\dwg\misc\mktg\hle-1xx-02-xxx-dv-xx-xx-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 hle-1xx-02-xxx-dv-xx-xx-xx
|
